![instacal software manual instacal software manual](https://i.ebayimg.com/images/g/jsYAAOSwWbJdcqbI/s-l640.jpg)
- Instacal software manual driver#
- Instacal software manual manual#
- Instacal software manual archive#
- Instacal software manual windows 7#
Be sure to keep the “Flow Outlet” valve (purple) closed during the measurement.
Instacal software manual manual#
Wait for the beeps and follow the instructions in the manual (page 41, point 5). Start the “Set Zero” procedure: in the top menu, set “Set Flow Level” to “Brown”, “Analysis Type” to “Set Zero” and click on Start. Press OK, and the first half of the top menu will become clickable.Ģ2. Restart the HPFM software and create a new project (“File” – “Open Project” – fill in “New Project” fields).Ģ1. After saving, close the HPFM software (important!) and copy the last lines (everything below and including ) from the CD’s “HPFM.ini” into the local program folder’s “HPFM.ini”.Ģ0. Alternatively, instead of changing the directories in “Settings”, edit them manually in the “HPFM.ini” file, and avoid the “Settings” menu altogether.ġ9. You’ll later need to copy these lines from the original “HPFM.ini” file. IMPORTANT: When you change settings, the “HPFM.ini” file resets all predefined calibration values to 0 (everything below and including ).
Instacal software manual archive#
In the HPFM software, open “Settings” and enter a correct Data Log Path, Archive Path, Project Path and Calibration Path (we’re using the pre-created folders in the program directory):Ĭ:\Program Files (x86)\Dynamax\HPFM\Data LogĬ:\Program Files (x86)\Dynamax\HPFM\ArchiveĬ:\Program Files (x86)\Dynamax\HPFM\Project (created manually!)Ĭ:\Program Files (x86)\Dynamax\HPFM\Calibration 004 V, at maximum pressure (560 kPa) the output should be.
![instacal software manual instacal software manual](https://www.mccdaq.com/images/photos_500/DT9837A_2_500.jpg)
At zero pressure, values should be less than. Run a device/communication test, via “Test” – “Analog”.ġ4. On tab “CH 2”, enter the following values:ġ3. On tabs “CH 0”, “CH 1” enter the following values:ġ2. On the first tab, compare the settings to the following screenshot and change values, if necessary.ġ1. Click on the “Board#…” entry in the device list, then click on the fourth symbol from the left, which shows a board and hand (“Configure”).ġ0. Start InstaCal (from the desktop icon or start menu). To make sure everything installed nicely, go to “Control Panel” – “Device Manager” (German version: “Gerätemanager”) and look for “DAS Component”.ĩ. When it’s done, you will see a popup window saying “USB Carrier installed”:Ĩ.
Instacal software manual driver#
Connect the HPFM (USB plug under the roof of the HPFM) to your computer using a USB cable and follow the driver installation instructions. Copy the file “CB.CFG” from C:\Program Files (x86)\Dynamax\HPFM\ICalUL to directory C:\Program Files (x86)\Measurement Computing\DAQ.ħ.
Instacal software manual windows 7#
Here’s our own version of a software installation guide for Windows 7 (64-bit), which also contains some necessary steps that weren’t mentioned in the official manual. 3 by Dynamax was no different: the installation process encompassed many pages of a manual that was, in some points, less detailled than we would have wished.
![instacal software manual instacal software manual](https://www.mccdaq.com/images/photos_500/miniLAB-1008_500.jpg)
The more specialized your device, the more complicated it usually is to set it up, and the HPFM Gen. If you don’t find the Urban Dictionary definition for HPFM satisfying: High Pressure Flow Meters are used to measure the hydraulic conductivity of plant roots, stems and more. A colleague and I recently tried to set up an HPFM at work.